HOW TO REPLACE A TUB (FOR NEWBIES).

How To Replace A Tub (For Newbies).

How To Replace A Tub (For Newbies).

Blog Article

Request A Quote

What are your opinions concerning A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a new one is also a reasonably tough task. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have currently acquired a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic due to the restricted access that is usually the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
    Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
    If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the tap in position with the manufacturer given backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Setting up the Bath tub


    Using both wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small points.
    The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
    To mount taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
    Activate the supply of water as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and also the normal outlet for leaks.
    Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has been used a minimum of when as this will certainly resolve it right into its final position.

    Getting ready for the Setup


    First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.

    Tiling Around the Tub


    In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    As a person who reads on Tools You Need to Install a New Bathtub , I was thinking sharing that editorial was a good idea. I beg you take a moment to distribute this blog if you enjoyed it. We thank you for reading our article about Tools You Need to Install a New Bathtub .



    Appointment

    Report this page